Plumbing Basics: A Must for Bathtub Installation
Plumbing Basics: A Must for Bathtub Installation
Blog Article
This great article in the next paragraphs on the subject of Installing A Bathtub is highly interesting. You should take a look.
Mounting a bathtub isn't specifically rocket science, but it does need solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably challenging project. If the old tub is easily obtainable, the job can move easily; if you need to open a wall to get rid of the old bathtub and position the brand-new bathtub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will certainly need an assistant to vacate the old bathtub and also set in the new one. Make certain you have actually qualified on your own for the work and also fit trying it. As opposed to working with a professional to take control of a halfway-completed project, it is better to think about employing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This article will help you install a brand-new bath tub in your shower room if you have actually already acquired a new tub and also do not need to transform the setup of your previous water pipes.
Your devices as well as product checklist need to comprise the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, then the first thing you must do is separate the water supply. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of getting rid of the existing taps can be rather troublesome because of the limited accessibility that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipes. As soon as the supply pipes have been eliminated, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any old sealing substance.
Before moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, after that you will call for reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines are in area in between the faucet and also the sink. Secure the faucet in position with the manufacturer supplied backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal tap connectors. The previous kind must be attached to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bathtub
Making use of the two wooden boards under its feet, place the bath tub in the called for placement. The wooden boards are practical in equally spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 tiny factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by checking the level and also changing the feet on the tub till the level checks out degree.
To install faucets, fit all-time low of the furthest versatile tap port to the appropriate supply pipeline by making a compression join; after that do the very same for the other faucet.
Turn on the water system and examine all joints and also brand-new pipework for leaks and tighten them if essential. Load the bath tub and likewise inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, repair the bathroom paneling as described in the maker's instruction manual. Tiling and sealing around the bath tub must wait until the tub has actually been used at least once as this will resolve it right into its final setting.
Planning for the Installment
First of all, the supporting framework provided with the bathroom needs to be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to ensure that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps unit to stop stress on the tub.
Fit the versatile tap ports to the bottom of both taps using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must now be ready to be fitted in its final setting.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to fracture an inflexible seal, causing the water to permeate the wall surface in between the bathroom and the tiling, causing complications with wetness and also possible leaks to the ceiling below.
You can pick from a variety of coloured sealants to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, as well as can securing voids up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill the bathtub with water prior to securing, to enable the motion experienced when the tub is in use. The sealer can fracture rather very early if you do not think about this movement before securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the market. It is suggested to fit the floor tiles making use of water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was guided to that write-up on How to Install a Bathtub Yourself from a good friend on another web address. Please take the time to share this blog posting if you appreciated it. I am grateful for your time. Kindly pay a visit to our website back soon.
View Report this page